Skip to content
Library
Image of Saphir Ultra X Central Pool Controller
Template

Saphir Ultra X Central Pool Controller

by IT-Service PenzenauerNo rating yet223 downloads

Content languageEnglish

Download · v1.0.0Add to favourites

Updated Jul 3, 2024

Download · v1.0.0

Description

Reading Values from Saphir Ultra X Pool Controller via RS232 Extension.

PINOUT: PIN2 (white) TxD --> RS232 Extension Rx PIN3 (green) RxD --> RS232 Extension Tx PIN5 (brown) GND --> RS323 Extension GND (yellow) not used

RS232 Settings: Baud Rate: 19200 Data length: 8bits parity: none stop bits: 1bit end sign: 0x03 checksum methode: none positiv acknowledge: 0x06 negativ acknowledge: 0x15

The SAPHIR device acts as a slave device, so everytime you want to read a value from the device you need to send command to the device and then it will send you an answer. In the example file this i have done with impulses but any other logic as useable.

also attached you can find an excel sheet to calulate the HEX Command according to the manual from SAPHIR.

Inputs and outputs · 61

NameTypeCommandUnit
001 serial numberComm\x02A001/\v<v>
006 water temperatureComm\x02A006/\v°C
021 level pHComm\x02A021/\v%
002 device typeComm\x02A002/\v<v>
003 HW VersionComm\x02A003/\v<v>
004 SW VersionComm\x02A004/\v<v>
007 pH valueComm\x02A007/\v<v.2>
008 Redox valueComm\x02A008/\vmV
009 CI valueComm\x02A009/\vmg/l
010 H2O2 valueComm\x02A010/\vmg/l
011 currentComm\x02A011/\vA
012 voltageComm\x02A012/\vV
020 level CuComm\x02A020/\v%
022 level H2O2Comm\x02A022/\v%
023 level ClComm\x02A023/\v%
030 error codesComm\x02A030/\v<v>
110 sleepmode (0/1)Comm\x02A110/\v<v>
290 desired temperatureComm\x02A290/\v°C
222 H2O2 weekly amountComm\x02A222/\vl
200 desired ph valueComm\x02A200/\v<v.2>
240 desired Cl valueComm\x02A240/\vmg/l
241 desired Redox valueComm\x02A241/\vmV
247 Cl BoostComm\x02A247/\vl
249 Cl Hybrid weekly amountComm\x02A249/\vl
223 H2O2 BoostComm\x02A223/\vl
130 CAN-Module relay 12-16Comm\x02A130/\v<v>
102 Cu daily amountComm\x02A102/\vg
006 water temperatureComm\x02\x52\x30\x30\x36\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x36\x03
001 serial numberComm\x02\x52\x30\x30\x31\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x31\x03
021 level pHComm\x02\x52\x30\x32\x31\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x33\x03
022 level H2O2Comm\x02\x52\x30\x32\x32\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x34\x03
023 level ClComm\x02\x52\x30\x32\x33\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x35\x03
007 pH valueComm\x02\x52\x30\x30\x37\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x37\x03
011 currentComm\x02\x52\x30\x31\x31\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x32\x03
012 voltageComm\x02\x52\x30\x31\x32\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x33\x03
008 Redox valuetComm\x02\x52\x30\x30\x38\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x38\x03
002 device typeComm\x02\x52\x30\x30\x32\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x32\x03
003 HW VersionComm\x02\x52\x30\x30\x33\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x33\x03
004 SW VersionComm\x02\x52\x30\x30\x34\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x34\x03
020 level CuComm\x02\x52\x30\x32\x30\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x32\x03
009 Cl valueComm\x02\x52\x30\x30\x39\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x39\x03
010 H2O2 valueComm\x02\x52\x30\x31\x30\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x31\x03
030 error codesComm\x02\x52\x30\x33\x30\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x33\x03
241 read Redox TargetComm\x02\x52\x32\x34\x31\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x37\x03
130 read CAN-Module relay 12-16Comm\x02\x52\x31\x33\x30\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x34\x03
130 CAN-Module relay 16 (Light) toggleComm\x02\x57\x31\x33\x30\x2F\x30\x30\x31\x32\x38\x2F\x35\x38\x30\x03
290 desired temperatureComm\x02\x52\x32\x39\x30\x2F\x30\x30\x30\x30\x30\x2F\x35\x37\x31\x03
200 desired pH valueComm\x02\x52\x32\x30\x30\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x32\x03
241 write desired Redox TargetComm
222 H2O2 weekly amountComm\x02\x52\x32\x32\x32\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x36\x03
240 desired Cl valueComm\x02\x52\x32\x34\x30\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x36\x03
110 sleepmode [0/1]Comm\x02\x52\x31\x31\x30\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x32\x03
270 start BackwashComm\x02\x52\x32\x37\x30\x2F\x30\x30\x30\x30\x30\x2F\x35\x37\x34\x03
102 Cu daily amountComm\x02\x52\x31\x30\x32\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x33\x03
130 CAN-Modul relay 12 toggle (Countercurrent)Comm\x02\x57\x31\x33\x30\x2F\x30\x30\x30\x30\x38\x2F\x35\x37\x38\x03
130 CAN-Modul relay 13 toggle (Massage)Comm\x02\x57\x31\x33\x30\x2F\x30\x30\x30\x31\x36\x2F\x35\x37\x37\x03
130 CAN-Modul relay 14 toggle (Rollo_open)Comm\x02\x57\x31\x33\x30\x2F\x30\x30\x30\x33\x32\x2F\x35\x37\x35\x03
130 CAN-Modul relay 15 toggle (Rollo_close)Comm\x02\x57\x31\x33\x30\x2F\x30\x30\x30\x36\x34\x2F\x35\x38\x30\x03
249 Cl Hybrid weekly amountComm\x02\x52\x32\x34\x39\x2F\x30\x30\x30\x30\x30\x2F\x35\x37\x35\x03
223 H2O2 BoostComm\x02\x52\x32\x32\x33\x2F\x30\x30\x30\x30\x30\x2F\x35\x36\x37\x03\r\n
247 Cl BoostComm\x02\x52\x32\x34\x37\x2F\x30\x30\x30\x30\x30\x2F\x35\x37\x33\x03

FAQ

No questions have been answered yet.

Ratings and comments

No ratings or comments yet.

Questions and answers

  1. keine verbindung zur Poolsteuerung

    Open

    Martin Müller

    ich kann leider keine Verbindung zu einer Saphir Ultra X über RS 232 aufbauen und bekomme somit keine Werte ausgelesen. hat sich was geändert oder könnte ein anderer Fehler vorliegen? meine Einstellungen sind Serielles Protokolls: Keines Abfragezyklus: 5s Protokolldaten: Baudrate: 19200 Anzahl Datenbits:8 Stopbits:1 Parität: keine Pause:0,01 Endkennzeichen:0x03 Prüfsummenverfahren:keines Positive Bestätigung:0x06 Negative Bestätigung:0x15

    vielen lieben dank im Voraus und Schöne Grüße Aus Vorarlberg

    Martin Müller

    Elektroinstallation Montafonerbahn Aktiengesellschaft A-6780 Schruns Tel:+436646218790

    [email protected] www.montafonerbahn.at

    No replies

Report this entry

Report abuse

You have to be logged in to report an entry. Log in