Skip to content
Library
Image of Alfen Wallbox
Template

Alfen Wallbox

by Alfen B.V.No rating yet2,036 downloads

Content languageEnglish

Download · v1.0.0Add to favourites

Updated Oct 21, 2021

Download · v1.0.0

Description

For additional information you can join the website Downloads-Alfen. There you can find flyers, manuals, certifications, etc. If you want to buy a new charging station or wallbox, please take a look here. You are able to add additional commands to the template. Therefore you will find information in the modbus register mapping (download files).

Important The Eve Single Pro-line and Double Pro-line are also available in compliance with calibration law. Also these devices are supported by this template.

Inputs and outputs · 16

NameTypeUnit
Voltage Phase V (L1-N)Modbus<v.1>
Voltage Phase V (L3-N)Modbus<v.1>
Voltage Phase V (L2-N)Modbus<v.1>
Reactive Power Phase L1Modbus<v.3>
Reactive Power Phase L2Modbus<v.3>
Reactive Power Phase L3Modbus<v.1>
AvailabilityModbus<v.1>
Modbus Slave Max Current valid timeModbus<v.1>
Active Load Balancing Safe CurrentModbus<v.1>
Charge using 1 or 3 phasesModbus<v.1>
Real Power Phase L1Modbus<v.1>
Real Power Phase L2Modbus<v.1>
Real Power Phase L3Modbus<v.1>
Real Power SumModbus<v.1>
Modbus Slave Max CurrentModbus<v.1>
Charge using 1 or 3 phasesModbus<v.1>

FAQ

No questions have been answered yet.

Ratings and comments

No ratings or comments yet.

Questions and answers

  1. can you read if a vehicle is connected?

    Open

    Tom Vandendael

    Is there a way to see, if a Vehicle is connect with the charging station?

    I think is need to use this register? Mode 3 state - 1201 - 1205 - 5 - R - String - n.a - 61851 states

    How do I need to read this data with Loxone?

    1 reply

    1. Marcel Stangrecki

      Hello Tom,

      i had seen the required information in Alfen ACE service Installer Program.

      Socket 1 Mode3 state as started in the IEC 61851 standard. State A (Cable connected to EVSE) State B (EV Connected to EVSE) State C (EV charging) State D (EV charging (ventilation required)) State E (No cable/car connected) State F (Error/Unknown)

      https://en.wikipedia.org/wiki/IEC_61851 See the table with Mode 3.

      with best regards Marcel Stangrecki

  2. Modbus TCP template

    Open

    Marcel Stangrecki

    Hello Alfen, hello Loxone,

    at what time we can download an Modbus TCP template for the Alfen Wallboxes? You have also been provided in Master (Loxone) and Slave (Alfen Wallbox) Mode.

    In your document "Modbus Slave TCP/IP - Implementation of Modbus Slave TCP/IP for Alfen NG9xx platform" and Version 2.3 (30.10.2020) you described the 89 datapoints of Modbus by one Socket for an wallbox. But the actual template can been show up to ca. 20 datapoints.

    with best regards Marcel Stangrecki

    No replies

  3. Gen1 miniserver

    Open

    Wouter Leroy

    Hello, does this also work with a miniserver Gen. 1? Or do you need a Modbus extension (I don't think so as it goes through TCP/IP)? I can't see the modbus template getting into my config software. Are there special things needed in the wall box? Thanks.

    1 reply

    1. Pieter BDP

      Will also work on Gen. 1 No modbus extension needed. Only network connection on Wallbox

  4. wrong sensor names in Template

    Open

    Michael Stolz

    Hi Creator, Pls. check naming of your sensors in template. According to your TCP/IP Register the "Reactive Power Phases L1 to L3" are "current Phases L1 to L3". If I am right, pls. change your template. Regards Michael

    No replies

  5. Fahrzeugstatus auslesen

    Open

    Roland Eichlseder

    Hallo Ersteller,

    Wie kann man den Fahrzuegstatus auslesen? Mode 3 wäre ja ideal dafür aber Loxone hat keine Möglichkeit String auszulesen? Gibt es hier eine andere Möglichkeit?

    Danke im Voraus.

    1 reply

    1. Pieter BDP

      Hello,

      I think you mean this

      https://www.loxforum.com/forum/software-configuration-user-interface/343715-modbus-tcp-device-read-string

  6. Dynamisch laden

    Open

    David Janssen

    Hallo,

    Ik heb een Alfen laadpaal single pro die 3fase 11kw levert maximaal. Nu staat deze ingesteld op een vast laadvermogen. Is het mogelijk om de laadpaal het voertuig enkel te laten laden als er overtollige zonne energie is? Kan dit ingesteld worden via loxone?

    Momenteel staat de laadpaal reeds gekoppeld met de loxone app en kan ik alle vermogens zien die men huis en laadpaal verbruiken. ik heb reeds een meter aangesloten op men digitale teller via zijn poort.

    Mvg David

    No replies

  7. Open

    Welvaarts Elektro

    Werkt deze template ook voor de nieuwe serie Eve Double Plus van dit jaar? Volledige functionaliteiten of zijn er beperkingen? Aansturen bidirectioneel etc.

    No replies

Report this entry

Report abuse

You have to be logged in to report an entry. Log in